简单简介
在3DM Mod站下载上古卷轴5：重置版最新的沉浸式VR（家庭自动化） Mod,由madrum制作。童话CORN在我们的平台上分享了这个免费且高质量的游戏模组,让玩家们可以享受到更加丰富的游戏体验。快来3DM Mod站下载并尝试吧!
详细介绍
Mod作者: madrum Mod版本: 1.1.0 Mod大小: 210 KB 更新时间: 2019-09-29 19:16:15 发布时间: 2019-09-29 19:16:15
详细说明
是否曾经在Skyrim上徘徊，感觉好像缺少了什么？可以肯定的是，您正在看到和听到的是微风，却没有感觉到，并且完全破坏了您的沉浸感，对吗？无需惊慌的朋友，此mod将帮助您。
您需要什么：
2.4GHz WLAN路由器（几乎每个人都在家中使用）
TP-Link HS100或HS110智能插头（适用于大多数插座类型）
带有手动/机械按钮的风扇。 （通电时必须立即打开-非常重要！）
大多数老粉丝都将具有此功能。较新的（尤其是较昂贵的）遥控器通常带有遥控器，并且可以在待机状态下启动（不是我们想要的）。
SKSE for Skyrim VR（从此处下载：http://skse.silverlock.org/）
这个mod;）
我知道这是一个有点昂贵的模块（硬件），但是风扇和智能插头在天际之外也很有用。
设定：
使用TP-Link for android / iOS（Kasa）中提供的应用程序配置智能插头，并将其命名为“ ImmersiveWindsPlug”。 （必须是这个名字！）
您的PC和智能插头必须连接到同一网络/路由器。 （LAN或WiFi）请注意，智能插头需要2.4GHz WiFi。
将风扇插入智能插头，并确保您可以使用该应用进行控制。
为Skyrim VR安装最新版本的SKSE。
安装此mod。
通过SKSE启动游戏并享受。 :)
组态：
一旦在启用了Mod的情况下启动游戏，就将在<Documents> / MyGames / Skyrim VR / SKSE中生成immersiveWinds.ini文件。
使用该文件进行以下配置。
您有2个选项可以运行此mod：
1.简单模式：
通过在immersiveWinds.ini文件中设置以下配置来激活：
bIntermittentModeEnabled = 0
它能做什么：
在室外打开风扇，在室内（房屋，洞穴等）关闭风扇
对于此模式，您要将风扇设置为较低的强度。
振荡的开启或关闭取决于游戏区的大小和您的个人喜好。
2.间歇模式：
安装mod时，此模式处于活动状态。 （因为大多数人使用它）
通过在immersiveWinds.ini文件中设置以下配置来激活：
bIntermittentModeEnabled = 1
它能做什么：
就像简单模式一样，在房屋内部它会关闭。
洞内和洞外有不同的优势，同时还要考虑到您所在位置的当前天气和海拔高度。
通过以不同的间隔不断切换插头的状态来获得不同的强度。
对于大多数用户而言，间歇模式的默认配置会很好，但是您可以完全自定义行为。
有7种不同的优势：
0：始终关闭。
1-6：间歇性或持续关闭/打开。
可以修改除0以外的每个强度。值是以秒为单位的时间间隔。这是强度等级1的示例：
fIntermittentL1Off = 2.0
fIntermittentL1RandomAddOff = 0.0
fIntermittentL1On = 1.2
fIntermittentL1RandomAddOn = 0.6
说明：
插头保持关闭状态2秒钟，然后再打开。
然后，插头保持开启状态1.2到1.8秒，然后再次关闭。该值在每个周期都是随机的，但始终在边界之间。
重复该循环直到强度改变。
将值fIntermittentLXOff或fIntermittentLXOn之一设置为0将针对该强度将插头的状态设置为恒定。
例：
fIntermittentL6Off = 0
fIntermittentL6On = 1.0
这会将插头打开直到强度改变。在这种情况下，随机值将无关紧要。
将两者都设置为0是无效的，并将导致该强度的默认值。
小于1的值，除0外，例如0.5，将四舍五入为1。这不适用于随机值。
另外，您可以自定义参数如何影响强度：
有4个类别：
位置基准值（例如iInsideBase）
海拔修改器
天气修改器
时间修改器
每个类别最多只能同时激活一个。
深度变量：
示例（使用默认值）：
外面+晚+高海拔+宜人的天气
-> 3 +1 +1 +1 = 5
因此，在这种情况下，结果强度级别将为5。
如果您认为自己的设置很棒，请随时在评论部分分享您的设置。
对于此模式，您要将风扇设置为最高强度。
振荡的开启或关闭取决于游戏区的大小和您的个人喜好。
建议：
我强烈建议使用封闭的耳机/入耳式风扇以及智能插头作为风扇，这会产生一些噪音，并可能使您分心。
您可以在同一插头上设置多个风扇，以增加效果的范围和一致性。
考虑使用Skyrim是有风的和/或有风的。
塔式风扇的振荡范围往往比普通风扇小，这也是一个不错的选择。我个人使用1个塔和1个普通风扇。
将风扇对准躯干高度。
附加的功能：
向播放器添加新的声音（清音）。有了喊声，人们可以召唤更强的风，持续30秒。如果需要快速冷却，则非常方便；）
喊叫仅在户外时有效！ （出于现实考虑）在安装时会自动得知该提示。
已知的问题：
如果您进入没有负荷屏/门的建筑物，风状态将无法正确更新，因为似乎无法检测到。 （除了可能检查x，y，z和加载的地图）
这不是一个大问题，因为仅影响了一些塔楼/废墟，但仍然受影响。如果您知道解决此问题的方法，请告诉我。
故障排除：
总的来说，这个mod应该与其他所有mod兼容。
该Mod无能为力。
->确保正确遵循上述设置指南，并且可以通过官方应用程序控制智能插头。您也可以尝试在<Documents> / MyGames / Skyrim VR / SKSE中的immersiveWinds.ini文件中将“ bUseUdp”设置为1。如果仍然无法正常工作，请给我写一条消息，并包含位于<Documents> / MyGames / Skyrim VR / SKSE中的immersiveWinds.log文件和immersiveWinds.ini文件。因此，我可以找出问题所在。如果这些文件不存在，则说明您的安装出现问题。 -> SKSE无法正常运行（请确保您通过SKSE启动Skyrim），或者此模块未正确安装。
如果发现错误，请在“错误”部分中创建它。
路线图：
我可能会研究目前使用其他硬件通过红外信号直接控制风扇的方法。这样还可以设置风扇的强度，以增加浸入系数。 （thx brentw89）这将是此Mod的附加功能，不能替代当前的硬件（TP-Link）。
我目前正在这里尝试这个东西：http://dangerousprototypes.com/docs/USB_IR_Toy_v2
我还想到了另一个使用相同技术添加另一个沉浸增强因子的mod。敬请关注。
——————————————————————————————————————————
Ever wandered through Skyrim and felt like something was missing? It sure is that cold breeze, that you're seeing and hearing, but not feeling and it's completly ruining your immersion, right? No need to panic friend, this mod will help you out.
What you'll need:
2.4GHz WLAN Router (almost everybody has this at home)
TP-Link HS100 or HS110 Smart Plug (available for most socket-outlet types)
A fan with manual/mechanical buttons. (It has to turn on instantly when powered - very important!)
Most old fans will have this feature. Newer (especially the more expensive) ones tend to come with remotes and start in standby (not what we want).
SKSE for Skyrim VR (Download from here: http://skse.silverlock.org/)
This mod ;)
I know this is a kinda expensive mod (the hardware), but both, the fan as well as the smart-plug are also useful outside of skyrim.
Setup:
Configure the smart plug using the provided app from TP-Link for android/iOS (Kasa) and name it "ImmersiveWindsPlug". (It has to be exactly this name!)
Your PC and the smart plug have to be connected to the same network/router. (LAN or WiFi) Notice that the smart plug needs a 2.4GHz WiFi.
Plug the fan into the smart plug and make sure you can control it using the app.
Install the latest version of SKSE for Skyrim VR.
Install this mod.
Start up the game via SKSE and enjoy. :)
Configuration:
Once you started the game once with the mod enabled, the immersiveWinds.ini file will get generated in <Documents>/MyGames/Skyrim VR/SKSE.
Use that file for the following configuration.
You have 2 options to run this mod:
1. Simple Mode:
Activate by setting the following configuration in the immersiveWinds.ini file:
bIntermittentModeEnabled=0
What it does:
Switch the fan on when outside, switch it off when inside (houses, caves, etc.)
For this mode you wanna set the fan to a lower strength.
Oscillation on or off depends on the size of your play area and your personal preferences.
2. Intermittent Mode:
This mode is active when you install the mod. (because the majority uses it)
Activate by setting the following configuration in the immersiveWinds.ini file:
bIntermittentModeEnabled=1
What it does:
Inside houses it will turn off, just like the simple mode.
Outside and in caves there are different strengths, also taking into account the current weather and altitude of the location you're at.
The different strengths are achieved by constantly switching the state of the plug at different intervals.
For most users the default configuration of the intermittent mode will be fine, however you can completly customize the behaviour.
There are 7 different strengths:
0: Always off.
1-6: Intermittent or constantly off/on.
Each strength except 0 can be modified. The values are time intervals in seconds. Here is an example for strength level 1:
fIntermittentL1Off=2.0
fIntermittentL1RandomAddOff=0.0
fIntermittentL1On=1.2
fIntermittentL1RandomAddOn=0.6
Explanation:
The plug stays off for 2 seconds, then switches on.
Then the plug stays on for 1.2 to 1.8 seconds and switches off again. The value is random every cycle but always between the boundaries.
This cycle is repeated until the strength changes.
Setting one of the values fIntermittentLXOff or fIntermittentLXOn to 0 will set the state of the plug to be constant for that strength.
Example:
fIntermittentL6Off=0
fIntermittentL6On=1.0
This sets the plug to on until the strength changes. The random values won't matter in this case.
Setting both to 0 is invalid and will result in the default values for that strength.
Values less then 1 except 0, e.g. 0.5, will get rounded up to 1. This doesn't apply to the random values.
Additionally you can customize how the parameters affect the strength:
There are 4 Categories:
Location Base Values (e.g iInsideBase)
Altitude Modifier
Weather Modifier
Time Modifier
Only one (at most) of each category can be active at the same time.
The variables in depth:
Example (using the default values):
Outside + Night + High Altitude + Pleasant Weather
-> 3 + 1 + 1 + 0 = 5
So the resulting strength level would be 5 in this case.
If you think you've found a great setup, feel free to share your settings in the comments section.
For this mode you wanna set the fan to the highest strength.
Oscillation on or off depends on the size of your play area and your personal preferences.
Recommendations:
I highly recommend using closed headphones/In-Ears as the fan, as well as the smart plug, will generate some noise and might distract you from the game.
You can setup multiple fans on the same plug to increase the range and consistency of the effect.
Consider using Skyrim is Windy and/or Blowing in the Wind.
Tower fans tend to have a smaller oscillation range than normal fans and are also a good option. Personally I use 1 tower and 1 normal fan.
Aim the fan(s) at torso height.
Additional Features:
Adds a new (unvoiced) shout to the player. With the shout one can summon stronger winds for a duration of 30 seconds. Handy if you need a quick cooldown ;)
The shout only works when outside! (For realism) The shout is learned automatically on installation.
Known Issues:
The wind state won't update correctly if you go inside a building without a load screen/door because there seems to be no way to detect it. (Except maybe checking x,y,z and the loaded map)
This is not a big issue, because only a few towers/ruins are affected, but still. If you know a way to fix this, please let me know.
Troubleshooting:
In general this mod should be compatible with every other mod.
The mod doesn't do anything.
-> Make sure you followed the above setup guide correctly and can control the smart plug via the official app. You can also try setting "bUseUdp" to 1 in the immersiveWinds.ini file located in <Documents>/MyGames/Skyrim VR/SKSE. If it still doesn't work write me a message and include the immersiveWinds.log file and immersiveWinds.ini file located in <Documents>/MyGames/Skyrim VR/SKSE. So I can track down the problem. If these files do not exist, something went wrong with your setup. -> Either SKSE is not working (make sure you start Skyrim via SKSE), or this mod wasn't installed correctly.
If you notice a bug please create it in the bugs section.
Roadmap:
I'll might investigate controlling a fan directly via infrared signals using other hardware then currently. This will allow setting the strength of the fan as well to increase the immersion factor. (thx brentw89) This will be an additional feature for this mod, not replacing the current hardware (TP-Link).
I'm currently trying out this thing here:
http://dangerousprototypes.com/docs/USB_IR_Toy_v2
I also thought of another mod that uses the same technique to add another immersion enhancement factor. Stay tuned.
文件说明
Mod截图
相关作品
我的世界 1.7.10因果空岛整合包 | 上古卷轴5 女子高中生校服制服整合包MOD | 上古卷轴5：天际 ESO高精灵护甲MOD | 《火炬之光2》仓库MOD | 死或生5：最后一战 心铁拳风间准人物套装MOD | 我的世界 1.7.2矿物透视MOD |